Software Downloads
DLA_Logic Software
Download for Windows V1.0.4
V1.0.4 Release Notes
1. Fixed an issue where text for resources loaded during startup failed to switch correctly between Chinese and English.
2. Fixed an issue where text in waveform measurements failed to switch correctly between Chinese and English.
3. Fixed an issue where text in parameter measurements failed to switch correctly between Chinese and English.
4. Fixed an issue with zooming (enlarging/shrinking) when using multiple screens.
Download for macOS (Apple Silicon) V1.0.1
V1.0.1 Release Notes
1. Fixed English/Chinese translations within the software.
2. Fixed issues with saving and opening files in the Mac version of the software.
Download for macOS (Intel) V1.0.1
V1.0.1 Release Notes
1. Fixed English/Chinese translations within the software.
2. Fixed issues with saving and opening files in the Mac version of the software.
USB Tester Software
Applicable product models: C1 / C2 / FNB48S / FNB48P / FNB58 / FNAC-28
Note: lOS and MacOS system do not currently support the use of.
DPS-150 / IPS3608 Software
Instructions for use
1. Basic Function Interface
① Waveform Display Area：Records, stores, and deletes waveform data, including voltage and current. When viewing a single waveform, you can zoom in and out using the mouse scroll wheel.
② Output Voltage and Current Settings: Change the output voltage and current values of the current preset group (changes are temporary and not saved; the device will revert to initial values after reboot).
③ Data Group Data: Click on a data group to set preset voltage and current values. Up to 6 different preset values can be saved.
④ Measurement Switch: Measures output capacity and energy. Measurements are reset upon closing and reopening.
⑤ Brightness Settings: 14 levels (Higher level means brighter backlight).
⑥ USB Interface: Product Model / Firmware Version / Communication Rate / Communication Port / Device Address / Online Status
⑦ Basic Information: Input Voltage / Output Voltage / Output Current / Output Power / Temperature
Display / Status Display
Control Device On/Off Status On This Interface
Basic Function Interface
2. Advanced Function Interface
① Sequential Output: Within the specified range of sequence numbers and loop counts,
sequentially output voltage and current parameters.
Click "Start" to execute sequential output (other interfaces are locked and inactive). Numbers
that have been executed show "OK", while numbers that haven't been executed show "Waiting".
Click "Pause" to maintain the current sequence output. Click "Continue" to execute subsequent
steps according to the set delay.
Manual Mode: Click "Single Step" for testing, testing proceeds according to the number of clicks.
Stopping will maintain the current sequence output.
② Current Sweep: With fixed voltage, the current is scanned and output within the set range
according to the step current and delay, commonly used in constant current mode. Voltage
setting needs to be greater than 0V; Starting current, ending current range: 0.000A5.000A (if the
starting and ending values are the same, it's invalid); Step current range: 0.001A5.000A; Delay
time: 1s~86400s. Click "Start" to execute current scanning output (other interfaces are locked
and inactive). Click "Stop" to stop the scan and close the output.
③ Voltage Sweep: With fixed current, the voltage is scanned and output within the set range according to the step voltage and delay, commonly used in constant voltage mode. Current setting needs to be greater than 0A; Starting voltage, ending voltage range: 00.00V30.00V (if the starting and ending values are the same, it's invalid); Step voltage range: 00.01V30.00V; Delay time: 1s~86400s. Click "Start" to execute voltage scanning output (other interfaces are locked and inactive). Click "Stop" to stop the scan and close the output.
Advanced Function Interface
3. PC Software Connection
① Turn on the device and connect it to the computer using a Micro data transfer cable.
② After connection, select the communication port. You can view it through Device Manager in Computer Management.
③ Click "Connect". Once "Connected" is displayed in the left text box, the connection is successful.
※ NOTE: During the PC software connection process, the device buttons will be locked and cannot be operated.
Firmware Upgrade by PC Software
① On the device's About page, ensure that the device address matches the device address displayed in the PC software.
② Connect the device to the computer using a Micro data transfer cable. Confirm the port and click "Connect" on the PC software.
③ Once the connection is successful, click on "Firmware Upgrade" above, then click "BOOT/Restart."
④ The computer will recognize the device as a USB flash drive. Copy the firmware to the USB flash drive. After successful copying, the device will automatically start the firmware upgrade process.
⑤ Observe the upgrade progress percentage. After the upgrade is completed, the device will
restart. If the upgrade fails, please contact customer service immediately.
Firmware Upgrade Interface
FD10 Software
YMOBD is a practical tool for vehicle diagnosis based on Android and iOS operating system. It has the characteristics of simple operation and accurate data, and is suitable for the long-term use of owners and users.
More Details
Keep your car away from hidden dangers and make driving fun!
Connect and communicate with OBD adapter through Bluetooth:
Real-time data stream
Request current powertrain diagnostic data
Freeze frame
When a trouble code appears in the emission system, the ECU stores the data when the trouble code appears
Dashboard
It can collect car engine data in real time, such as speed, speed, water temperature, voltage, fuel consumption, etc. It has two modes of day and night, and has HUD display function.
DTC monitoring
It can detect the fault code information of the current vehicle and provide professional solutions for the detected fault codes of the vehicle.
Fault indicator detection
MIL provides engine system fault detection.
Monitor status
Monitor status since DTCs cleared and Status of tests run at least once per trip.
Travel analysis
It can record every driving process of the vehicle. Analyze and summarize the driving mileage, average fuel consumption, driving time, driving speed and other data.
Performance Testing
It can conduct customized DIY tests on the acceleration performance, braking performance and distance of the vehicle, and provide the corresponding test result report.
Osxygen sensor test results
Allow access to the on-board oxygen sensor monitoring test results.
Components/systems test results
Allow access to the results of On-Board Diagnostic monitoring tests for specific components/systems.
IR40 APP
Instructions for use
1. Basic Function Interface
① Waveform Display Area：Records, stores, and deletes waveform data, including voltage and current. When viewing a single waveform, you can zoom in and out using the mouse scroll wheel.
② Output Voltage and Current Settings: Change the output voltage and current values of the current preset group (changes are temporary and not saved; the device will revert to initial values after reboot).
③ Data Group Data: Click on a data group to set preset voltage and current values. Up to 6 different preset values can be saved.
④ Measurement Switch: Measures output capacity and energy. Measurements are reset upon closing and reopening.
⑤ Brightness Settings: 14 levels (Higher level means brighter backlight).
⑥ USB Interface: Product Model / Firmware Version / Communication Rate / Communication Port / Device Address / Online Status
⑦ Basic Information: Input Voltage / Output Voltage / Output Current / Output Power / Temperature
Display / Status Display
Control Device On/Off Status On This Interface
Basic Function Interface
2. Advanced Function Interface
① Sequential Output: Within the specified range of sequence numbers and loop counts,
sequentially output voltage and current parameters.
Click "Start" to execute sequential output (other interfaces are locked and inactive). Numbers
that have been executed show "OK", while numbers that haven't been executed show "Waiting".
Click "Pause" to maintain the current sequence output. Click "Continue" to execute subsequent
steps according to the set delay.
Manual Mode: Click "Single Step" for testing, testing proceeds according to the number of clicks.
Stopping will maintain the current sequence output.
② Current Sweep: With fixed voltage, the current is scanned and output within the set range
according to the step current and delay, commonly used in constant current mode. Voltage
setting needs to be greater than 0V; Starting current, ending current range: 0.000A5.000A (if the
starting and ending values are the same, it's invalid); Step current range: 0.001A5.000A; Delay
time: 1s~86400s. Click "Start" to execute current scanning output (other interfaces are locked
and inactive). Click "Stop" to stop the scan and close the output.
③ Voltage Sweep: With fixed current, the voltage is scanned and output within the set range according to the step voltage and delay, commonly used in constant voltage mode. Current setting needs to be greater than 0A; Starting voltage, ending voltage range: 00.00V30.00V (if the starting and ending values are the same, it's invalid); Step voltage range: 00.01V30.00V; Delay time: 1s~86400s. Click "Start" to execute voltage scanning output (other interfaces are locked and inactive). Click "Stop" to stop the scan and close the output.
Advanced Function Interface
3. PC Software Connection
① Turn on the device and connect it to the computer using a Micro data transfer cable.
② After connection, select the communication port. You can view it through Device Manager in Computer Management.
③ Click "Connect". Once "Connected" is displayed in the left text box, the connection is successful.
※ NOTE: During the PC software connection process, the device buttons will be locked and cannot be operated.
Firmware Upgrade by PC Software
① On the device's About page, ensure that the device address matches the device address displayed in the PC software.
② Connect the device to the computer using a Micro data transfer cable. Confirm the port and click "Connect" on the PC software.
③ Once the connection is successful, click on "Firmware Upgrade" above, then click "BOOT/Restart."
④ The computer will recognize the device as a USB flash drive. Copy the firmware to the USB flash drive. After successful copying, the device will automatically start the firmware upgrade process.
⑤ Observe the upgrade progress percentage. After the upgrade is completed, the device will
restart. If the upgrade fails, please contact customer service immediately.
Control Device On/Off Status On This Interface
Firmware Upgrade Interface
- Choosing a selection results in a full page refresh.